-
EPOXY PRODUCTS
-
Floor Coatings
- PRIMER WG 032
- WALL WG 034
- BRV SC 105
- BRV SC-200 K
- PRIMER SC 210
- PRIMER SC 215
- PRIMER SC 220
- SC Z-230 Self Leveling C Komponent
- PRIMER SC 270
- PRIMER SC 325
- DECOFLOOR SC 330
- FLOOR SC 470
- SC 600
- WALL SC 605
- WALL SC 605-C
- BRV SC 610 • Solvent-Free Epoxy Topcoat
- BRV SC 620 • Solvent-Free Textured Epoxy Topcoat
- BRV SC 625 SOLVENT-FREE EPOXY TOP COAT NON-SLIP FLOOR PAINT
- FLOOR SC 645
- SC 650 ST
- FLOOR SC 902
- FLOOR SC 903
- BRV SC 905 • CHEMICAL RESISTANT SOLVENT-FREE EPOXY TOP COAT FOR VERTICAL SURFACES
- FLOOR SC 950
- FLOOR SC 1200
- FLOOR AC 6380
- ROAD AC 6388
- Waterproofing Products
- Repair Anchorage and Assembly Products
- Joint Filler and Ceramic Adhesive Products
- Wood Protection Adhesive and Lamination Products
- Natural Stone Protectors
- Water Reservoir & Drainpipe Insulation Products
- Anticorrosive Products For Metal Surfaces
- Thinners
-
Floor Coatings
-
POLYURETHANE PRODUCTS
- FLOOR COVERING AND PAINTING PRODUCTS
- WATERPROOFING PRODUCTS
- STRUCTURAL REINFORCEMENT REPAIR ANCHOR INSTALLATION PRODUCTS
- WOOD PROTECTOR, ADHESIVE AND LAMINATION PRODUCTS
- NATURAL STONE PROTECTIVE PRODUCTS
- ANTICORROSIVE PRODUCTS FOR METAL SURFACES
- CONCRETE SURFACE PROTECTION AND POLISHING PRODUCTS
- THINNERS
-
ACRYLIC PRODUCTS
- WATERPROOFING PRODUCTS
- FLOORING AND PAINTING PRODUCTS
- INTERIOR AND EXTERIOR INSULATION & PAINT PRODUCTS
- SPECIAL FLAME RETARDANT INSULATION PRODUCTS
SEAL TK 090
DEFINITION
Public Works Pos. No: 04.559/02
USAGE AREAS
All kinds of concrete and mineral surfaces, mosaic surfaces, natural stones (marble, travertine, slate, granite, synthetic and natural stone flooring)
Type | TS EN 1504-2/ April 2008 Principle 5 (PR): 5.1 Physical Resistance / Surface Improvement Coating Application (C) |
Colour | Transparent |
Thinner Density Waste Package Application Methods Application Temperature Shelf Life Waiting time between coats Drying Time Full Drying and waterproof Equipment Cleaning
| Ready to use 0,85 gr/cm³ Between 100 gr-250 gr/m² at single coat depending on the roughness and suction condition of the application surface 4 kg, 15 kg metal kovalarda brush, roller, air or airless gun +5 ºC -+ 30 ºC 1 year in unopened package 30–40 min /at 25 ºC 24 hours / 25 ºC 7 days Synthetic thinner |
SURFACE PREPARATION
The surfaces to be applied must be free from oil, dust, rust, dirty and all kind of residues.
APPLICATION CONDITIONS
* The product is ready for use.
* It is applied at least two coats on high suction, textured and rough surfaces. It should be applied with a break of at least 30 minutes etween both coat.
* The full performance of the product must be tested at least 24 hours later.
* Full performance is at maximum level after 7 days.
* Good ventilation should be provided in applications to be performed in confined spaces.
* Easy to apply,
* Has high penetration ability.
* Resistant to UV rays.
* Provides water and oil repellencyl.
* Protector against alkaline and acidic stain forming products (Tea, coffee, ketchup, mayonnaise, coke, etc),,
* Prevents salt spitting on the surface where it is applied..
* Does not change the color of natural stone
* Since it does not form a film layer on the applied surface, it does not prevent vapor diffusion on the surface.
* Easy to clean.