-
EPOXY PRODUCTS
-
Floor Coatings
- PRIMER WG 032
- WALL WG 034
- BRV SC 105
- BRV SC-200 K
- PRIMER SC 210
- PRIMER SC 215
- PRIMER SC 220
- SC Z-230 Self Leveling C Komponent
- PRIMER SC 270
- PRIMER SC 325
- DECOFLOOR SC 330
- FLOOR SC 470
- SC 600
- WALL SC 605
- WALL SC 605-C
- BRV SC 610 • Solvent-Free Epoxy Topcoat
- BRV SC 620 • Solvent-Free Textured Epoxy Topcoat
- BRV SC 625 SOLVENT-FREE EPOXY TOP COAT NON-SLIP FLOOR PAINT
- FLOOR SC 645
- SC 650 ST
- FLOOR SC 902
- FLOOR SC 903
- BRV SC 905 • CHEMICAL RESISTANT SOLVENT-FREE EPOXY TOP COAT FOR VERTICAL SURFACES
- FLOOR SC 950
- FLOOR SC 1200
- FLOOR AC 6380
- ROAD AC 6388
- Waterproofing Products
- Repair Anchorage and Assembly Products
- Joint Filler and Ceramic Adhesive Products
- Wood Protection Adhesive and Lamination Products
- Natural Stone Protectors
- Water Reservoir & Drainpipe Insulation Products
- Anticorrosive Products For Metal Surfaces
- Thinners
-
Floor Coatings
-
POLYURETHANE PRODUCTS
- FLOOR COVERING AND PAINTING PRODUCTS
- WATERPROOFING PRODUCTS
- STRUCTURAL REINFORCEMENT REPAIR ANCHOR INSTALLATION PRODUCTS
- WOOD PROTECTOR, ADHESIVE AND LAMINATION PRODUCTS
- NATURAL STONE PROTECTIVE PRODUCTS
- ANTICORROSIVE PRODUCTS FOR METAL SURFACES
- CONCRETE SURFACE PROTECTION AND POLISHING PRODUCTS
- THINNERS
-
ACRYLIC PRODUCTS
- WATERPROOFING PRODUCTS
- FLOORING AND PAINTING PRODUCTS
- INTERIOR AND EXTERIOR INSULATION & PAINT PRODUCTS
- SPECIAL FLAME RETARDANT INSULATION PRODUCTS
SEAL TK 075
DEFINITION
One component water-based, transparent concrete and natural stone protector with high content of alkyl alkoxysilane based high purity
Public Works Pos.No.: 04.559/01
USAGE AREAS
All kinds of concrete and mineral surfaces, mosaic surfaces, natural stones (marble, travertine, slate, granite, synthetic and natural stone flooring)
Type | TS EN 1504-2/ April 2008 Principle 5 (PR): 5.1 Physical Resistance / Surface Improvement Coating Application (C) |
Colour | White - Transparent when applied |
Outlook | Bright |
Thinner | Ready to use |
Density Solid Matter Chloride penetration (concrete) Water absorption test (concrete) Flash Point - ASTM D 3278-82 | 1,02 gr/cm3 %20 %7 %5-8 >90°C |
Waste | Between 0,100 kg–0,250 kg/m2 at single coat depending on the roughness and suction condition of the application surface |
Package | 1 kg, 4 kg, 15 kg in plastic bins |
Application Methods | brush, roller, air or airless gun |
Application Temperature | +5 °C + 30 °C |
Shelf Life | 1 year |
Drying Time | 24hours/25 °C |
Equipment Cleaning | Water |
SURFACE PREPARATION
The surfaces to be applied must be free from oil, dust, rust, dirty and all kind of residues.
APPLICATION CONDITIONS
The product is ready for use. It is applied at least two coats on high suction, textured and rough surfaces. . It should be applied with a break of at least 1 hour between both coat. The full performance of the product must be tested at least 24 hours later. Good ventilation should be provided in applications to be performed in confined spaces.
*Easy to apply,
* Has high penetration ability.
* Resistant to UV rays.
* Waterproof.
* Can be applied on humid surfaces.
* Reduces flowering, algae and dirt formation on concrete surfaces to be applied.
* Protector against alkaline and acidic stain forming products (Tea, coffee, ketchup, mayonnaise, coke, etc),
* Uygulandığı yüzeylere antibakteriyel etkisi yaparak hijyenik ortam yaratır.
* Prevents surface wears because it forms a hard and durable surface.
* Creates a decorative and aesthetic appearance on the surfaces.
* Creates slightly wet appeaarance on the applied surface.
* Low VOC content.