POLY PRIMER WATER BASED FLOOR AND WALL INSULATION PRIMER
DEFINITION
Water-based acrylic copolymer floor and wall insulation primer with specific chemical and physical properties ready to use, fast drying, high physical strength.
* Ready to use.
* Single component
* Excellent waterproof
* Practical and easy to apply
* Water-based environment friendly.
* High strength and UV resistance.
* Enables insulation of applied walls and soils and also allows them breathing
USAGE AREAS
* On the screed applied terraces and roofs of the buildings
* The floor, terraces and roofs forming a wet volume and water ponding.
* In basic curtain concrete.
* Interior and exterior of the buildings.
* In factory warehouse areas.
* On old surface with problem
* On garden concrete and stone surfaces.
* In sports areas with concrete and asphalt floors.
|
Type |
TS 7847 |
|
|
Colour |
Transparent |
|
|
Density Dust Drying Time Touch Drying time Minimum Application Temperature Dry Heat Resistance Water Vapor Permeability |
1,03 gr/cm3 1-2 hours /25 °C 3-4 hours/25 °C + 5 ºC -25 °C/ +180 ºC TS EN ISO 7783-2:2002 Class 1 Sd < 5m Class 1 =1,230 Appropriate |
|
|
Package |
4 kg – 17 kg |
|
|
Shelf Life |
12 months |
|
| Uygulama Yöntemleri
Uygulanacak Zemin Sıcaklığı Katlar arası uygulama Süresi Ekipmanların Temizliği |
Fırça, Rulo, Havasız Tabanca
+5 ºC +30 ºC 2 saat/25 °C Su ile temizlenir. |
USAGE METHOD
The floor to be applied must be cleaned from oil, dirt, rust, dust and all kinds of residues. The fact that the floor is strong and durable affects the performance of the product positively. It is ready to use. Application can be done with brush, roll or airless gun.
REQUIREMENTS TO BE CONSIDERED ON SURFACES THAT PRODUCT APPLIED
Surfaces such as glass, ceramics and glazed ceramics without water emulsion should be roughened before application. (Joints of surfaces with joint spacing should be cleaned with a wire brush and the residues should be removed from the surface.) No surface smoothing is required on normal calendered concrete surfaces that no surface hardener used. Oil, dirt and the residues and formations that willprevent the surface emulsion must be completely removed on all other surfaces. The surface must be roughened again on concrete surfaces, in areas where surface hardener, cure agent products and paraffin derivatives used.
WASTE
It may vary according to the physical characteristics of the walls and soils to be applied. On avarege, it can be calculated on concrete surfaces as 100-150 gr/m² before plaster as primer, on porous surfaces of gazbeton type as 300 gr/m², on screed surfaces as 100-150 gr/m²
SAFETY WARNINGS
Before use, pay attention to the safety warnings on the package, see the Material Safety Data Sheet if necessary. Do not breathe, avoid skin and eye contact, do not swallow, use appropriate work safety material. In addition to the danger of fire and explosion, necessary precautions are taken in order not to pollute the surrounding area. Apply in well ventilated environments.
* The product should be stored at 5-35°C.
* The product should not be exposed to direct sunlight.
* The opened product should be kept in its package by closing the cover tightly.
NOTE
BRV,BRV reserves the right to make improvements/revision on product and this document in time. This Technical Data Sheet invalidates the Technical Data Sheet previously issued for this product and shall be valid for 5 years. The user must make sure that the technical document in his hand is the latest version, if necessary, contact our company to inquire about the update of the document. It is the responsibility of the user to ensure that the product is properly used for its intended purpose and the validity of the application conditions and forms. BRV Epoxy Paint does not accept any warranty claims for consequences of the failure to apply the products as recommended, for work accidents, direct or indirect damage and losses.